Show us your setup!

[Speakman]

go the book monitor stand __b

[Xenolightning]

go the book monitor stand __b

Hell yea. Perfect height too lol. Best use of that uni textbook yet!

[Scorched_onion]

Took apart my case and dusted it after 3 years of dust collecting and replaced the old 4850 with a new 6850. Spoilered cause of amount of pictures. Also flipped around my side panel intake fan so its now exhaust. Because it didn't have a filter and was responsible for most of the dust in there. Also redid some of my cables to make it more tidy. And wrapped some things in black tape to make them less noticeable. You cant see the small details in this pic but you can see the bottom of the case and the b/a tidyness. Tucked away alot of cables near the top too.

Spoiler :

[O-L-W-A-G]

Soo much dust

[Scorched_onion]

Soo much dust

Yep, all gone now though. 2 of my 3 intake fans have foam and then dust filters too. So most of it was from the side fan with no filter. Which is now an exhaust fan haha.

[StarDream]

Does your PC live on the floor?

[Scorched_onion]

Does your PC live on the floor?

Nope sits ontop of my desk funnily enough.

Show us your setup!

[Emrico1]

Show us your setup!

[pop]

[Xsannz]

WAS

Show us your setup!

NOW

Show us your setup!

[Erelyes]

Starbucks mug huh... do they not sell coffee in Chch?

Show us your setup!

Show us your setup!

I5-2500k, lazy 4.0, megahalems, P67 Pro
Corsair 120gb SSD
HD5870
Phantom, Deathadder, etc

[Hmmmgood]

[/URL][/IMG]

[/URL][/IMG]

[/URL][/IMG]

So far its just an EK block with XSPC parts i brought from Xsannz.

Next step is 3 fan radiator,DDC pump and get a block from EK for the 590.

[Hmmmgood]

[/URL][/IMG]

[/URL][/IMG]

[/URL][/IMG]

So far its a EK LT block with an XSPC pump/res and 240 rad i got off Xsannz.

Next step is a 3 fan rad,D5 pump and il get a block for the 590 aswell.

[mycoolcar]

Nice. What sort of temps and overclock are you getting?

[Dr. Acula]

My wee gaming hub, about to start building myself a desk this week with a sheet of 18mm MDF I picked up today, should be able to hold all of this plus 1 or 2 more monitors which are in the pipeline.

Now, time to finish off that last half litre of Canadian Club I have sitting on my desk

[Hmmmgood]

Nice. What sort of temps and overclock are you getting?

It lives at 4.6 24/7 with 1.33v,idles 35ish and seems to max around 55.I was  hoping for better temps as these are hardly better than the asetek dual rad kit i was using previously.

Iv  had this cpu at 5.4 really easy with the old cooler for the superPI  thread,im gona have another tinker during this week and see if i can get  abit more from it.

I think the pump in these xdpc kits are fairly average.I notice in your pics that your v put the cpu before the rad.I thought it was better to have the coolest water from the rad to the cpu?

Yours looks great with the clear coolant.

[mycoolcar]

My clear coolant is just distilled water

Loop order has no bearing on real world temps. This is because the water will eventually reach an equilibrium where all water in the loop is a similar temp, with the rad just removing heat as its generated. How long this takes depends on the amount of water in the loop. IMO more rad space would probably reduce your temps a bit further.

[Lvl10]

[O-L-W-A-G]

What is on the other warpad?

[Lvl10]

razer nostromo lol dual wielding warpads
... next level comfort!

[O-L-W-A-G]

Agreed loving my warpad aswell.

[Retardobot]

After having my setup sit on the dining room table for the past month with all it's guts hanging out, I finally transplanted it back to my office.

[Xenolightning]

Is that a Thompson?

[Retardobot]

It is.

It works fine. It's the Mrs. I have a good LinkSys sitting in my cupboard, but I can't be fucked setting it up as I can't remember the admin password.

[O-L-W-A-G]

admin? If it's not there is a reset button.